Description
Engine Revision Set Lambretta XXL
We offer you two revision sets for your Lambretta engine. In the large set you will find all the parts you need to fit a bare engine housing with bearings, studs, shaft seals, silent blocks and bushings. Or to rebuild an old engine case completely new.
are included in the delivery:
1. complete engine bearing set and bearing bushesdl/GP. It can also be used for the Li/SX models if the spacer ring is not installed in the maghousing. In this case the wider NU2205 bearing of the dl/GP will fit the earlier models as well.
-
6305 ball bearing drive side crankshaft – SKF or FAG
-
NU2205 ball bearing alternator side – SKF or FAG
-
ball bearing rear wheel – bgm PRO
-
6004 Ball bearing auxiliary shaft – SKF or FAG
-
Coupling bush dl/GP – bgm PRO
-
Needle bearing -K- (24x28x10 mm) Spider/pinion LI/SX/TV/GT (2 pieces) – SKF or FAG
-
needle bearing -K- (16x22x12 mm) Auxiliary shaft/motor housing – SKF or FAG
-
needle bearing -K- (20x24x10 mm) Main shaft/gearbox cover plate – SKF or FAG
-
bearing bush auxiliary shaft
-
washer auxiliary shaft
-
washer needle bearing main shaft/gear 1.
2. Fits 125, 150, 175 and 200 cc. MB Developments. All used circlips except the one in the maghousing (Art. No. 8002140).
4. Complete O-Ring Set MB Developments. For main shaft, rear brake arm, shift and clutch shaft.
5. All bushings: shift shaft, kick starter inside and outside.
6. All engine studs, dowel pins, grease nipples:
-
complete stud bolt set Engine cover fits Series 1-3 – bgm PRO
-
complete stud bolt set Gearbox cover plate – MBD
-
stud bolt M6 x 25 mm Fan wheel housing – 3 pieces
-
stud bolt M6 x 21 mm Cover plate Rear wheel bearing – 4 pieces
-
stud bolt M6 x 28 mm chain tensioner – 2 pieces
-
mating pins motor housing and gearbox cover plate – 4 pieces
-
lubrication nipple M8 x 1,25 brake arm – 1 piece
7. Disk kick starter shaft MBDin 1.0 mm and 1.5 mm for spacing the kick starter shaft out on the outside of the engine cover
8. kick starter piston bolt MB Developments
9. silent block set bgm PRO
10. pressure plate set for the chain tensioner.
11. screw hexagon socket M6 x 16 mm (4 pcs.) to fix the cover plate for the 6305 bearing on the drive side.
12. L-ring impeller housing
13. all oil plugs: check, drain, vent – Casa Lambretta
14. screw M6 x 18 mm -ISO 7380- with flat hexagon socket head for fixing the shift fork plus M6 spring washer corrugated
15. Gearbox shims bgm PRO in 2.00 mm, 2.20 mm and 2.40 mm and 2.60 mm.
16. Clutch nut M14 x 1.5
17. Clutch nut locking plate
18. Clutch compensating washers set bgm PRO (0.8 mm, 1.0 mm, 1.2 mm, 1.4 mm and 1.6 mm)
19. Shift spring SIL
20. switching ball Ø=7.9 mm – 2 pieces
21. half moon wedge fan wheel
22. cable clamping plate in maghousing – MBD
23. screw set maghousing/cylinder cover – MBD
24. M6 washers – 100 pieces – in set of 100 cheaper
25. M6 stop nuts – 100 pieces – in a set of 100 pieces cheaper
With the shaft seal set you can choose between MB Developments (inner crankshaft seals made of FPM), Jockeys Boxenstop (inner crankshaft seals made of FPM) and Casa Lambretta (all shaft seals made of FPM).
Some parts are not included in the kit as the choices are too wide. This concerns parts for the clutch revision, the front sprocket, the chain tensioner, the chain, the cover plate for the 6305 bearing, cylinder studs, kick starter shaft, the shift claw and the adjusters on the engine.
AI-translation
Reviews
There are no reviews yet.